Close

Page 3 of 3 FirstFirst 123
Results 31 to 36 of 36
    1. Kit: , by (VIP/Sponsor) JunkGTZ is offline
      Builder Last Online: Feb 2018 Show Printable Version Email this Page
      Model Scale: 1/8 Rating:  Thanks: 0
      Started: 12-10-14 Build Revisions: Never  
      Supported Kit Bashed Build in Progress

      "Be careful what you ask for because you just might get it." My mother used to say that and it has now become reality (once again). I was searching for a Jag body to possibly fit to my RC, but didn't want to do any alteration to an intact body. They are hard to get and tend to run out of my price range on eBay. Well this carcass showed up and the price was right, but it was in rougher shape than I imagined. Aside from the whole hood and nose being cracked in two, the roof was cracked and the floor pan too. Lots of parts are missing too, but the basic body shell has all the pieces. I separated the floorpan and firewall, and started figuring where I will alter it. My vision for this is as a speedster and i will use the roof as part of the back deck. For now it will sit while I finish up the Corvette GSR. I have lots of things to work through before I move forward. Suggestions welcome. Shots attached.

      Jaguar XK Junk Heap-jag-junk-pile-jpg

      Jaguar XK Junk Heap-jag-hood-crack-jpg

      Jaguar XK Junk Heap-jag-roof-crack-jpg

      Jaguar XK Junk Heap-jag-project-floor-pan-jpg

      Here's the reconstituted shell.
      Jaguar XK Junk Heap-jag-jpg

      Here's the direction I want to go in.
      Jaguar XK Junk Heap-jaguar-xke-brg-5-jpg

      Mine will have a 1 inch shorter wheelbase and I am mulling over how to cover my wider track. I'd prefer not to do flares like the GSR project, but rather widen the body in more subtle ways. That will sort it self out in time Lord willing.

      Ciao!

      P.S. Included in the heap of parts, was the back end of a T-Bucket which has a side cracked off of it. Message me if interested.


      Jaguar XK Junk Heap

      Build Photos

      Jaguar XK Junk Heap-jaguar-xke-brg-1-jpg 


      Show Complete First Post

      Show Your Support

      • This build may not be copied, reproduced or published elsewhere without author's permission.
        Please note: The first post will be displayed at the top of every page.
    JOIN THE SMC ALLIANCE NOW

  1. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    I know my XK Junk Heap is not much compared to some of the more refined work going on here, but I figure I'll pursue it to the end and learn what I can from you folks. Inspiration is helpful especially about now when I'm getting tired of waiting on this thing to be finished! Here's the latest.

    Time for working on this has been very limited so I throw on some putty Jaguar XK Junk Heap for a few minutes and come back later in the day to sand Jaguar XK Junk Heap , then fill again as needed. I worked on bonding the aluminum top of the body to the plastic - It was already screwed into some plastic tabs I "welded" in as it were with MEK. I then removed the screws and used a reaming tool and hand truned the holes to counter sink some screws in. They still stick up a little but it's about as good as it is going to get. Then I went underneath and used a few pieces of fabric ice hockey tape which is light weight and I covered it with epoxy Jaguar XK Junk Heap more or less "fiber" reinforcing it. (Thanks to Two Kids No Sleep for that tip). I filled cracks, screw holes and sanded in the hopes I could primer Jaguar XK Junk Heap the thing, but the weather has been cold and wet and I have no heated space to paint. I also evened out the grill in front and evened out the back. I'm back with the original spoiler in back but with less pitch to it. It's just as well that the weather has been unsuitable as I've had some projects for my work to tackle and I really cannot get to absorbed in this thing right now much as I am having fun getting it to the point of painting. That will tell me a lot about places I need to fill and smooth again. I'm hoping the weather dries up and warms up enough to get a coat of primer Jaguar XK Junk Heap on it but that will depend on openings in my schedule coinciding with the weather. School starts up again next week and I have some busy weekends coming up too. Anyhow, here's some shots - slow progress this.

    Jaguar XK Junk Heap-img_1767-jpg

    Jaguar XK Junk Heap-img_1768-jpg

    Jaguar XK Junk Heap-img_1769-jpg

    Jaguar XK Junk Heap-img_1770-jpg


    Jaguar XK Junk Heap
    QUOTE QUOTE #32

  2. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    The weather warmed up so I went for it and shot a coat of primer Jaguar XK Junk Heap . I'm both encouraged and discouraged. It's good to see it one color, but there's nothing like a coat of paint to expose how much more body work you have to do to be ready for top coating. I can run my hands over the whole thing and think it's pretty smooth and the paint says otherwise. Nonetheless, it was a step forward - a little bit anyway. I made a new headrest detail which still needs lots of finishing but it's more to my liking than what I've had before. I need to remove the screws, fill and put the front on it as well as figure out how it will be attached.

    Jaguar XK Junk Heap-img_1774-jpg

    Jaguar XK Junk Heap-img_1775-jpg

    Jaguar XK Junk Heap-img_1776-jpg

    Jaguar XK Junk Heap-img_1777-jpg


    Jaguar XK Junk Heap
    QUOTE QUOTE #33

  3. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    Lots of sanding Jaguar XK Junk Heap , more filling, and reworking a few spots including the rear end. The weather warmed up enough to spray another coat of primer Jaguar XK Junk Heap and here's where we are at. The primer Jaguar XK Junk Heap shows me what needs more work and this time around it looks pretty good. There are a few more spots and then it will be more primer Jaguar XK Junk Heap and wet sanding Jaguar XK Junk Heap . I am eager to finish coat it! I wish there wasn't so much left to sort out. Rear and front spoilers need to be worked out, the tail light mounting needs to be figured out more thoroughly and some other details so I've got a good while before I can do the British Racing Green on it.

    Jaguar XK Junk Heap-img_1780-jpg

    Jaguar XK Junk Heap-img_1781-jpg

    Jaguar XK Junk Heap-img_1782-jpg

    Jaguar XK Junk Heap-img_1783-jpg


    Jaguar XK Junk Heap
    Attached Images Attached Images Jaguar XK Junk Heap-img_1774-jpg Jaguar XK Junk Heap-img_1775-jpg 
    QUOTE QUOTE #34

  4. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    Lots of sanding Jaguar XK Junk Heap , more filling, and reworking a few spots including the rear end. The weather warmed up enough to spray another coat of primer Jaguar XK Junk Heap and here's where we are at. The primer Jaguar XK Junk Heap shows me what needs more work and this time around it looks pretty good. There are a few more spots and then it will be more primer Jaguar XK Junk Heap and wet sanding Jaguar XK Junk Heap . I am eager to finish coat it! I wish there wasn't so much left to sort out. Rear and front spoilers need to be worked out, the tail light mounting needs to be figured out more thoroughly and some other details so I've got a good while before I can do the British Racing Green on it.

    Jaguar XK Junk Heap-img_1780-jpg

    Jaguar XK Junk Heap-img_1781-jpg

    Jaguar XK Junk Heap-img_1782-jpg

    Jaguar XK Junk Heap-img_1783-jpg


    Jaguar XK Junk Heap
    QUOTE QUOTE #35

  5. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    Haven't been able to do anything big with it, but did some work on the back end fashioning all new metal pieces, integrating the original license plate surround as well. I also wanted to figure out how I would attach the tail light lenses I had roughed out last year. Speaking of tail lights - I ended up ruining the one of the lenses I had (took off too much) and thought I had more of the material, but I was lacking enough redo it so I went in a new direction with a discarded reflector off a bike. It gets me a little closer to a cross between a Series 3 tail lamp and a more modern look. I still have to tweak it some, but at least I know if I mess it up I have enough to do another pair. I changed the angle of the spoiler and will remake that too for a tighter fit. I also need to make a front spoiler.

    Jaguar XK Junk Heap-img_1786-jpg

    Jaguar XK Junk Heap-img_1785-jpg


    Jaguar XK Junk Heap
    QUOTE QUOTE #36

  6. JunkGTZ's Avatar VIP/Sponsor
    Name
    Larry
    Join Date
    Dec 2012
    Posts
    270
    Jaguar XK Junk Heap
    Did a few more small things. Reworked the rear spoiler into a front spoiler. Fashioned a new rear spoiler and I am not totally satisfied, but it works for now. I did more shaping on the tail lights and will probably do some wrap around bumpers such as were on the Series 3 XKE to go over the top of the tail lights. I still have to go back over and fill some spots and will have to retouch the primer Jaguar XK Junk Heap before wet sanding Jaguar XK Junk Heap , but final prep for paint is a ways off. I'm going to fabricate a seat, (for a driver to be made later), cover the passenger side with a metal lid and do a small instrument panel w steering wheel. I also have to redo the headlight buckets a bit and figure out the attachment for the lenses. Here's some shots.

    Jaguar XK Junk Heap-img_1787-jpg

    Jaguar XK Junk Heap-img_1788-jpg

    Jaguar XK Junk Heap-img_1789-jpg


    Jaguar XK Junk Heap
    QUOTE QUOTE #37

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Top