Close

Page 5 of 5 FirstFirst 1 2 3 4 5
Results 61 to 69 of 69
    1. Kit: , by (VIP/Sponsor) xken is offline
      Builder Last Online: Jan 2020 Show Printable Version Email this Page
      Model Scale: 1/8 Rating:  Thanks: 1
      Started: 05-02-19 Build Revisions: Never  
      Supported Scratch Built

      Tommy Ivo's Showboat 1/8 Scale-sb00-jpg Tommy Ivo's Showboat 1/8 Scale-4motorbodyoff-jpg

      I built this model as a young lad with my father's help at times and have been intrigued by it ever since and always wanted to scratch build Tommy Ivo's Showboat 1/8 Scale it. Building four engines from scratch just seemed a task that I was not ready to tackle. Recently I have been extremely busy building, designing and developing model ship kits fro M.E. and have been looking for a personal project to keep me from going KNOTS. Anyway I came across a site offering a 1/8 scale Buick Nailhead cast resin Tommy Ivo's Showboat 1/8 Scale engine and after a little discussion reached a fair deal to purchase four engines knowing that some parts would require significant modifications.

      In doing research, I discovered that the Showboat itself underwent changes as it evolved to its final configuration as seen above along with an image of it in its earlier days with no body. Could very well be test runs. I also discovered on the H.A.M.B. site photos posted by the original builder and the replica builder which will be my reference resource. The Revel kit while in its day a good model but has a few major discrepancies the greatest being the oil pan configurations. I have also seen the die-cast model as well which is also creative in some details. Working from photos only and my own research I may also have to get creative with some small details.

      The initial build challenges I for see are the alignment of the four engines and the centerline of the 14 exhaust pipes; two point down on the left bank of engines. Hopefully, Mr. Geometry and Mr. Physics will help me along the way.

      First will be the clean up, drilling and milling of the cast parts. Since I have not done any extensive work with resin Tommy Ivo's Showboat 1/8 Scale I will now have a new learning experience and this will be a mixed media build. If anyone out there has any information or detailed personal pictures please share I will need all the help I can get on information.


      Tommy Ivo's Showboat 1/8 Scale
      Show Complete First Post

      Show Your Support

      • This build may not be copied, reproduced or published elsewhere without author's permission.
        Please note: The first post will be displayed at the top of every page.
    JOIN THE SMC ALLIANCE NOW

  1. Egon's Avatar Moderator
    Name
    egon
    Join Date
    Sep 2009
    Posts
    1,265
    Just stumbled on his video explaining how it works, if you havn't seen it.
    QUOTE QUOTE #62

  2. xken's Avatar VIP/Sponsor
    Name
    Kenneth
    Join Date
    Aug 2008
    Posts
    2,339
    Thanks yes there are a few out there. The replica is up for sale tomorrow at the Mecum Action in Kissamee, Florida. Lot # S150.

    I made a post earlier but it is not showing up. Some message saying it would be posted after admin review. Not had that one before.


    Tommy Ivo's Showboat 1/8 Scale
    "In wine there is wisdom. In beer there is strength. In water there is bacteria."
    Ken

    QUOTE QUOTE #63

  3. xken's Avatar VIP/Sponsor
    Name
    Kenneth
    Join Date
    Aug 2008
    Posts
    2,339
    The front axle is supported by a frame support on the right side but braces to the quick change unit on the left side.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-02-jpg

    The adapter plates are custom made and one modified.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-01-jpg

    Raised details added before adding the raised ribs.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-04-jpg

    Here is the finished unit ready for the axles to be added.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-09-jpg
    Here are the turned axle parts ready for assembly.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-12-jpg

    Using the old school CAD system (cardboard aided design) I fabricated the two support braces that straddle the quick change unit. This is the outboard brace pattern.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-13-jpg
    Here the brass axle brace is soldered in place to the frame.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-14-jpg
    .Inboard brace in place,
    Tommy Ivo's Showboat 1/8 Scale-front-axle-15-jpg

    The steering gear box built and soldered in place.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-16-jpg

    The engines is now bolted in place front and rear.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-18-jpg

    The 1 ton truck axle parts fabricated; the tricky part was milling a plumb bore for the cup shafts. The cup will be chrome plated Tommy Ivo's Showboat 1/8 Scale with the rest of the parts painted black.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-19-jpg

    Tommy Ivo's Showboat 1/8 Scale-front-axle-20-jpg

    The axles shafts are enabled to move in and out for final positioning and will be set with screws counter sunk on the bottom.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-21-jpg

    Adapter plates and grease fittings added.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-22-jpg

    Here is the grease fitting being turned; they are like the cherry on the top of a sundae.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-22a-jpg

    Here is a test fit of the wheel bolted in place.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-23-jpg

    Wheels turn freely with no sloppiness, good and tight.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-24-jpg

    Linkage will be next.


    Tommy Ivo's Showboat 1/8 Scale
    "In wine there is wisdom. In beer there is strength. In water there is bacteria."
    Ken

    QUOTE QUOTE #64

  4. xken's Avatar VIP/Sponsor
    Name
    Kenneth
    Join Date
    Aug 2008
    Posts
    2,339
    Moving on to the linkage I used soft aluminum rod for rough fitting of the linkage rods. The challenge was the bending around the quick change unit. All connections will be bolted for easy dis-assembly for final finishing and chrome plating.
    Tommy Ivo's Showboat 1/8 Scale-front-axle-25-jpg

    Tommy Ivo's Showboat 1/8 Scale-front-axle-26-jpg

    Tommy Ivo's Showboat 1/8 Scale-front-axle-27-jpg

    Tommy Ivo's Showboat 1/8 Scale-front-axle-28-jpg

    Tommy Ivo's Showboat 1/8 Scale-front-axle-29-jpg

    The steering rod required threaded ends to receive the tie rods for wheel adjustment.

    Tommy Ivo's Showboat 1/8 Scale-tie-rod-01-jpg

    Tommy Ivo's Showboat 1/8 Scale-tie-rod-02-jpg

    Tommy Ivo's Showboat 1/8 Scale-tie-rod-03-jpg

    Tommy Ivo's Showboat 1/8 Scale-tie-rod-04-jpg

    Next came the steering gear box with my initial thoughts of using bevel gears for the direction change. Both parts were bored .20" to the maximum allowable to maintain the size and scale and fit the gears.

    Tommy Ivo's Showboat 1/8 Scale-steering-gear-box-01-jpg

    Tommy Ivo's Showboat 1/8 Scale-steering-gear-box-02-jpg

    After having assembled the linkage and steering gear box and looking at pictures from Bruce of the original build I determined that the support arm and steering gear box needed to be moved forward slightly. This relocation on impacted the change of the steering arm and making it shorter.
    Tommy Ivo's Showboat 1/8 Scale-steering-gear-box-03-jpg

    This shows the relocated arm and steering gear box. I also drilled and tapped the vertical square rod from the steering arm up inside the steering gear box and added a 0-80 Tommy Ivo's Showboat 1/8 Scale bolt in top hole and the bolt will now turn the wheels for now.
    Tommy Ivo's Showboat 1/8 Scale-steering-gear-box-04-jpg

    Next will be the crankshaft dampeners for each bank of engines.


    Tommy Ivo's Showboat 1/8 Scale
    Last edited by xken; 01-12-20 at 08:14 PM.
    "In wine there is wisdom. In beer there is strength. In water there is bacteria."
    Ken

    QUOTE QUOTE #65

  5. Roger Zimmermann's Avatar Yearly Subscriber
    Name
    Roger
    Join Date
    May 2012
    Posts
    2,679
    Wow! A lot of small details taking a lot of time; I know that!
    QUOTE QUOTE #66

  6. xken's Avatar VIP/Sponsor
    Name
    Kenneth
    Join Date
    Aug 2008
    Posts
    2,339
    Roger thanks! Yes a great deal of small parts and I know from your work you know what it takes. Keep up the great work you are doing on your projects I enjoy watching your work as well.


    Tommy Ivo's Showboat 1/8 Scale
    "In wine there is wisdom. In beer there is strength. In water there is bacteria."
    Ken

    QUOTE QUOTE #67

  7. Roger Zimmermann's Avatar Yearly Subscriber
    Name
    Roger
    Join Date
    May 2012
    Posts
    2,679
    Thanks Ken! Unfortunately, it seems that the number of people who participate or building is decreasing.
    QUOTE QUOTE #68

  8. xken's Avatar VIP/Sponsor
    Name
    Kenneth
    Join Date
    Aug 2008
    Posts
    2,339
    Yes, I think you are correct sad but true. But I keep building as a form of pain management for my back with disintegrating discs; the focus on details takes away the pain. Also no deadlines I build at my pleasure and to share knowledge and experiences with others.


    Tommy Ivo's Showboat 1/8 Scale
    "In wine there is wisdom. In beer there is strength. In water there is bacteria."
    Ken

    QUOTE QUOTE #69

  9. Roger Zimmermann's Avatar Yearly Subscriber
    Name
    Roger
    Join Date
    May 2012
    Posts
    2,679
    Sorry to learn that you have such problem. As I'm probably about the same age, I'm building also for my pleasure, nothing more. Fortunately, I don't have pains or, better said, not yet.
    QUOTE QUOTE #70

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Quick Scale Calculator

 
Scale Calculator   Scale Factor   Real Size:     + Deluxe Scale Calculator
  1: th   Which equals Convert measurement: Reset or clear:  
  Any Scale   Scale Size:     + Deluxe Metric Calculator
 
Top