Close

How to make anything out of styrene
Goal amount for this year: 518 USD, Received: 415.00 USD (80%)
Scalemotorcars is a free and open community devoted to scale modeling. The heart and soul of Scalemotorcars is our global community of over 10,000+ contributors, millions of readers, and donors like yourself all united to share unlimited access to reliable information. Your donations keep Scalemotorcars freely available to everyone.

This years bandwidth costs, hosting service, domain registration, software licensing fees, and maintenance cost have a balance of $518 due by the end of August, (extended to the end of Septembers). Please help us keep Scalemotorcars growing by making a donation today.
Thank you.


How to make anything out of styrene How to make anything out of styrene How to make anything out of styrene How to make anything out of styrene How to make anything out of styrene
Accepted Payment Types

Page 2 of 2 FirstFirst 1 2
Results 16 to 17 of 17
    1. Kit: , by (VIP/Sponsor) Old Busted Hotness is offline
      Builder Last Online: Apr 2019 Show Printable Version Email this Page
      Model Scale: 1/8 Rating:  Thanks: 1
      Started: 01-30-11 Build Revisions: Never  
      Not Supported

      I've been asked by Management to show you the ancient art of styrene How to make anything out of styrene sculpting, so here goes. Today we're building an exhaust system with lots of curves, clamps and of course a muffler. These same techniques can be used to make any part, and in fact were used to make the engine.



      First, figure out where you want the pipe to go. In this case, it needs to make a 90 degree bend out of the turbo. Start by cutting a flat sheet to the shape you need. I used .060 styrene How to make anything out of styrene sheet here.



      Then cut a bunch of squares that fit the piece you just made. Glue one to the back...





      ... and trim around it. Don't worry about precision cuts, just get it in the ballpark.



      Repeat until the part is as thick as it needs to be.



      Rough cut with a Dremel How to make anything out of styrene sanding How to make anything out of styrene drum and X-Acto



      Final finish with an emery board or sanding How to make anything out of styrene stick.



      Test fit often during sanding How to make anything out of styrene .



      An exhaust that falls off the car is no good, so you need clamps. Two layers of .040 makes the back of the clamp...



      ... and a wrap of 1/32 half-round makes the band. Clothespins are real good for holding parts while the glue sets up.



      Now for the nuts & bolts. Roll some 1/8 hex rod under your knife to make a shallow cut all the way around.



      I hope you can see the cut. Next, make some cuts from the end to reduce the diameter down to the line you just cut. Once you've gone all the way around, you'll have:



      A nut with some "threads" sticking out. I suppose you could run a 00-90 How to make anything out of styrene die down there and really thread them if you wanted to, but since these parts are going to get rusted anyway, a rough cut is good enough.



      Assembled clamp.



      Now do it again. The elbow fits a 7/32 styrene How to make anything out of styrene tube that goes down along the firewall, but we need to transition again to the rocker panel.



      Same as before, build up enough layers to rough out the part, and fire up the Dremel How to make anything out of styrene .



      And now you've got this. I decided to make it one of those cheeseball flex pipes, but the camera battery died while I was documenting it. You can see in the final pic how it looks with some .005 strip wrapped around to simulate the flex pipe construction.



      You don't want to get a ticket, so we need a muffler. End panels are .060 and the wrap is .010, just go around until it's together. You could sculpt the muffler using layers, too, but making it hollow makes for a lighter part that uses a lot less material.



      Add more clamps, a cut-out pipe and a hanger, and now we've got a street-legal exhaust.


      How to make anything out of styrene
      Show Complete First Post

      Show Your Support

      • This build may not be copied, reproduced or published elsewhere without author's permission.
        Please note: The first post will be displayed at the top of every page.
    JOIN THE SMC ALLIANCE NOW

  1. red's Avatar Active Member
    Name
    Alan
    Join Date
    Jan 2013
    Posts
    14
    Now this is a useful article, well explained.
    Many thanks
    QUOTE QUOTE #17

  2. kmeaders@q.com's Avatar VIP/Sponsor
    Name
    Ken
    Join Date
    Oct 2010
    Posts
    696
    The most useful tutorial I have ever seen since I started scratch building 4 years ago.
    QUOTE QUOTE #18

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Quick Scale Calculator

 
Scale Calculator   Scale Factor   Real Size:     + Deluxe Scale Calculator
  1: th   Which equals Convert measurement: Reset or clear:  
  Any Scale   Scale Size:     + Deluxe Metric Calculator
 
Top